Posts Tagged ‘props’
Filed under: diy, haunted house, how to, props
HH Fencing
These work pretty well for keeping people away from frights but still allowing folks to see them.
You will need:
Scrap 2×4′s
screws
saw
drill to drive screws.
Cut two uprights about as tall as you want them. We went a little taller than waist high.
two 2x4s for horizontal bits.
2 2x4s for feet. 2 feet long is plenty. Just enough to get a sand bag or a cinder block on it.
scrap 2x4s for bracing.
Screw it all together. The feet get screwed into the bottom of the uprights. The bracing gets screwed into both the upright and the foot. The horizontal bits get screwed on the inside of the uprights (away from the public).
The horizontal bits can be put on with precision, we didn’t do this, they are not level. I think it adds to the atmosphere.
You can paint these with something to react in a black light or leave them un painted. 
When you put these up and together, try to cover joints with some fabric covering some foam or pointed away from the public.
We use these to keep folks away from props and to direct them towards other frights.
Remember that exposed screw points or heads or points of 2×4′s are an invitation for someone to get hurt. Which kind of ruins the experience for everyone, especially when they give you bad press or sue you. Not to mention feeling bad that someone got hurt.
Tags: diy, haunted house, how to, props
Permalink Comments (0) Michael Smith Jan 26, 2009
Filed under: diy, haunted house, how to, props
We needed a well for a prop.
What you will need.
55 gallon plastic drum.
Cardboard.
Scrap 2x4s
screws
Paint.
duct tape.
We took the bottom half of a plastic 55 gallon drum. We used a drum like the one below cut in half. I think any large bucket or barrel would work. I have seen large styrofoam plant pots that might work.
Screw the 2x4s about 8 inches apart around the drum vertically. Form the cardboard around the 2x4s attached to the drum. Tape it in place. Paint.
In the picture above, you can see some blue inside the well. This is the blue barrel. You can see the red strobe light we use to light up the fog. The skull and hand are mentioned below.
This prop has been modified many times since. Originally we had some lights in the bottom of it and cut a 6 inch hole in the side and fed fog from a fog machine into the well. Made for an eerie effect. The next year we added a pneumatic system to raise a skull and paper mache hand out of the well at people through the fog. This year the skull and hand did not move, the effect was to get people to look into the well expecting the skull and hand to reach for you and then have something behind the well grab at the person.
Tags: diy, haunted house, how to, props
Permalink Comments (0) Michael Smith Jan 19, 2009
Filed under: diy, haunted house, how to, props
I have tried to make these many times. There are plenty of other sites that have diagrams on them, and I will add mine here. I have used wood from freight palates (remove the planks, cut to length, glue and brad nail together), scrap paneling, ply wood (expensive and heavy, don’t do this), and have recently seen people using insulation foam (probably pretty light). Depending on the intended use, you pretty much can’t screw this up. Remember that people who see these usually see them in the dark and are pretty amped up. Perfection is not necessary.
I mostly just guessed the first one I built and then copied the results after I had one that looked ok. Use cardboard to lay it out, cut it out and assemble using tape. Once you have something you like, trace it out on the material you want to use and away you go.
I did some searching using the Google brain. Plans can be found here for coffin out of one sheet of plywood.
Tags: diy, haunted house, how to, props
Permalink Comments (0) Michael Smith Jan 12, 2009
Filed under: diy, haunted house, how to, props
I needed a small army of guys for a hallway in this year’s haunted house. As finding people to work the HH has always been a problem in the past, I needed to recruit some non living help. 
What you’ll need:
scrap 2×4′s
screws
foam
duct tape
landscaping fabric
saw (I used a circular saw)
screw driver (I used a cordless drill)
knife to cut foam (I used a $10 eclectic knife from the big box store)
stapler
hammer-tacker or staple gun
Note on measurements. The results of this project will be seen in the dark by people who are (hopefully) startled. Don’t worry about being precise.
For each guy you will need to cut the following.
A 2×4 for the shoulders. I roughly measured mine from shoulder to shoulder and cut a 2×4 to that length.
Two vertical pieces to make the mannequin tall. I roughly measured from the floor to my shoulders. Then cut two 2×4′s to this length.
One piece for a waist. Again, I measured my waist and cut a piece that long.
Two feet. I again guestimated what it would take for the guy to not tip over and cut two.
A 2×4 scrap to put the head on. I was using costume masks, so I measured one from the base to the top and cut a 2×4 down to that length.
Stand your two vertical lengths upright. Put the waist bit about waist high and screw it in.
Put the shoulder bit across the top and screw it down.
Put the feet on.
Toenail the head bit on.
Cut an arm-length of foam. Mine ended up being 4 inches x 4 inches by the length of my arm. Tape one end of it on top of the shoulder. Tape is cheap. Use enough tape. Repeat for the other arm. 
More in the next post.
Tags: carpentry, diy, haunted house, how to, props
Permalink Comments (0) Michael Smith Jan 2, 2009
Filed under: diy, haunted house, how to, props
This has been done ad nausium elsewhere, so it won’t be belabored much here. Simply cut tombstone shapes out of 1 inch insulation foam. Attach them at the bottom to scrap 2x4s. Paint a good stony color. Paint witty epitaphs on them. We usually try to put inside jokes on them. Or your pirate name.
Tags: diy, haunted house, how to, props, Toombstones
Permalink Comments (0) Michael Smith Dec 7, 2008
